How do you fix the bonnet removed error on Litter-Robot?

If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a solid blue light, you've been successful.

What does bonnet removed mean?

The bonnet functions as a cover and guard for the waste port as the globe rotates. The globe will not rotate without the bonnet installed. If a cycle is interrupted or the bonnet is removed, the unit will stop, and the yellow light will flash slowly, about 1x per second.

How to put bonnet on Litter-Robot?

Replace the bonnet, sliding the tabs on both sides into the slots in the base. Rotate the bonnet forward, aligning the tabs with the corresponding slots in the base. Snap the bonnet securely into the base. Press the Power button to turn the unit on.

How to remove bonnet from Litter-Robot 4?

Press and hold the latches on both sides of the bonnet, then lift and rotate the bonnet to its open position. Unlatch the bonnet, remove, and set aside .

What is the bonnet on the Litter-Robot 4?

Litter-Robot 4 features a bonnet that covers the globe and functions as a guard for the waste port as the globe rotates . Sensors on the unit detect if the bonnet is on or off. This ensures that Litter-Robot will not rotate if the bonnet has been removed.

What is an example of a bonnet?

bonnet noun [C] (METAL COVER) the metal cover over the part of a car where the engine is: I looked under the bonnet and clouds of smoke poured out.

What is the purpose of a bonnet?

Bonnets shield hair from friction and absorption into cotton pillowcases, preventing breakage, knots, and moisture loss as you sleep . Those with curly and coily textures have long utilized bonnets to preserve their curls, but straight and thin hair can also benefit.

Is it hard to change a bonnet?

Is the hood of a vehicle the hardest outer body part of a car to replace? As others have said so clearly, the hood, as well as the trunk lid, are both extremely easy to remove, replace and align on a modern car . Most are only held on with four bolts to a hinge plate.

Why is my Litter-Robot stuck on a solid red light?

If your unit's light bar is solid red, this indicates that the cat sensor has been triggered (kitty entered globe). The unit will cycle once the cycle delay countdown is up or if you press the Reset button. Learn more.

How do you fix a Litter-Robot cat sensor fault?

Check for obstructions that might prevent the cat sensor from functioning. Make sure Litter-Robot is on a firm, level surface. The cat sensor function can be affected if the unit is on carpeting or a litter mat. Check that there are no power cords running underneath the base of the robot that might obstruct movement. More items...

How to fix flashing yellow light on Litter-Robot?

If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle . Success: If your unit returned home and displays a solid blue light, you've been successful.

Litter Robot Bonnet Removed Error: Here's How to Fix it (2024)

Disclaimer: Some of the links in this article may be affiliate links; we will earn a commision, at no additional cost to you, if you make a purchase through one of our links.

It’s a good thing that modernized litter boxes are now an option. Litter Robot is a modern technology that offers big help to fur-parents. This device is specially designed with pre-programmed instructions that allow proper functioning.

However, just like any other technology, Litter-Robot may also malfunction. One of the common issues you may encounter when using the robot is the bonnet connections.

You’ve probably received a notification about your Litter-Robot bonnet removed error.

Is that why you’re here? Well, you’ve come to the right place! Stick around to learn more information.

Litter Robot Bonnet Removed Error: Here's How to Fix it (1)

Table of Contents

Why Do I Keep Receiving The notification litter robot Bonnet Removed Error?

This issue happens if the bonnet isn’t securely placed on the Litter-Robot. It restricts the globe from rotating and you’ll notice a yellow light blinking once per second.

Another reason might be the black key found at the back of the globe. It’s supposed to lift the bonnet if placed in the right slot.

However, if none of these two is causing the error, you can try the following solutions:

Save 35% on All Pet Supplies from Chewy

Re-assembling The Bonnet

1. Unplug The Litter-Robot

Turn off the litter box by pressing the ON/OFF button. Then, unplug the power supply blackjack from the back.

Recommended: Catlink vs Petkit full comparison

2. Remove The Bonnet

To release the bonnet, press the left and right tabs located in the front of the Litter Robot. After that, incline the bonnet top toward the back of the litter box.

3. Clean The Sensors

While the bonnet is removed, clean the two metal sensors using a damp cloth. It can be found on the left side of the bonnet.

4. Re-attach The Bonnet

Hold the bonnet with your two hands. Tilt the bonnet top away from your body so the two rear corner tabs are upright. Slip the tabs into the slots on the base. Next, tilt the bonnet top forward to drop the longer front tabs and insert them into the front slots.

To ensure that the bonnet is secured, press down on its sides and you should feel a snap and hear a ‘click’.

Check The Night-Light Connection

1. Unplug The Litter Robot

Turn off the litter box and unclip the bonnet.

2. Check The Wiring

Inside the bonnet, you’ll see wires and a micro connector. They’re attached to a small circuit inside the light housing. Make sure there’s a proper connection by pushing the micro connector into the circuit board.

If the issue still persists up to this point, you should replace the bonnet with a new one.

What Other Issues I May Encounter With My Litter-Robot?

Here are the other common issues you may encounter when using a self-cleaning litter box.

1. Cat Sensor Fault

Too much weight in the globe can trigger the Cat Sensor. It causes the Litter-Robot to stop mid-cycle and, sometimes, a red light will start blinking. These could be signs that you need to adjust the cat sensor.

Follow these steps to make adjustments to the Cat Sensor:

Turn off the Litter-Robot and remove the globe.
While the globe is removed, turn on the robot and check if the gear is turning.
If the gear is turning:
Turn off the Litter-Robot’s power.
Turn the base upside down so you can see the bottom surface.
Look for the round black adjustment foot.
Turn the adjustment foot clockwise twice (720°).
If the gear isn’t turning:
Push and release the Safety Line found in the base several times.
Do this until you hear a ‘clicking’ noise.
Reboot the Litter-Robot.
If at this point, the gear is turning, reattach the globe.
Let it complete a cleaning cycle. (This means that there’s no need for Cat Sensor adjustment).
In case this still doesn’t work, you may have to contact Litter-Robot customer service.
Reattach the globe and turn the Litter-Robot on.
Let the robot complete a cleaning cycle. If not, repeat step number 4

If the Litter-Robot keeps on stopping mid-cycle, contact their support team.

2. Rotation Error

This is how the globe rotation works: When your cat is done with its business, the globe rotates and moves through a sifter. All the clean litter will be separated from the dirty ones, and the remaining dirty litter will be placed in the waste drawer.

Litter Robot Bonnet Removed Error: Here's How to Fix it (2)

After that, the globe rotates back and will leave you with clean litter.

Recommended: How to reuse crystal cat litter

You may encounter your Litter-Robot turning the wrong way, and this happens due to one of these reasons:

Malfunction in the circuit board
Harness or magnetic sensor issue

In case you’re experiencing a rotation error in your Litter-Robot, it’s recommended to contact their customer service. You may probably need to replace some parts of the robot.

Customer Reviews

Here are some insights from the fur-parents who have used Litter-Robot:

1. Not Worth Buying

Litter-Robot is definitely expensive compared to a traditional litter box. Even though it’s an advanced technology, it’s still prone to malfunction.

2. Too Bulky

It looks big when you look at it, but it doesn’t have enough space for pretty large cats.

3. SafeCat System Is Surprisingly Effective

As soon as the cat put his paws on the ledge to take a peek inside the Litter-Robot, it immediately detected the cat’s weight and stopped the clean cycle.

4. The Whisker App Works Well

It gives accurate reports on the status of the Litter-Robot, and the waste drawer level. The app also provides health information about the cat, its daily input, and so much more.

Related: How to fix the Litter-Robot dump position fault

5. The Product Is Certainly Convenient

For some fur-parents, it’s an amazing product overall. The Litter-Robot is simple to use and easy to set up. It has worked quite well when it comes to eliminating waste odors.

Final Verdict

Litter Robot bonnet removed error is a common problem when using the self-cleaning litter box.

Most of the time, it’s simply because the bonnet isn’t correctly placed in the litter box. If that’s not the case; hopefully, the methods we’ve mentioned helped you fix the error.

If nothing worked for you, it’s probably time to change your Litter Robot’s bonnet.

Knowing what each light indicator means can also help you determine your robot’s status.

Phil Jonas